Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Murrieta Homeowners Choose Trane Air Duct Cleaning
Trane air duct cleaning means pulling the kind of fine reddish decomposed-granite grit and dry horse-arena dust out of return plenums that most coastal contractors never see. We’re an independent duct-cleaning practice, not a Trane-authorized shop, and we service XR80 and XR90 furnaces, XB13 condensers, and XV20i variable-speed systems across Southwest Riverside County. Since the Santa Ana winds push DG powder and equestrian dust through every attic penetration, Trane systems here load up faster than anywhere else in the valley. Call (855) 341-7672 and we’ll tell you straight what’s in there and what it takes to get it out.
We work on more Trane equipment than most Murrieta HVAC shops see in a year, because we’re duct specialists, not generalists. Our entire practice is built around one system: the air pathways inside your home. That focus means the blower wheel, evaporator coil, return plenum, and supply trunks on a Trane system get more of our attention than any condenser fan or compressor ever will.
Why Trust Duct Cleaning Murrieta for Your Trane Air Duct Cleaning?
Clay Gentry built Duct Cleaning Murrieta after years doing residential and light-commercial duct work across the Temecula Valley. He came up through the HVAC/R program at Mt. San Jacinto College in Menifee, then spent enough time inside Trane cabinets to know precisely where each platform leaks and collects debris. When we open a Trane XR80 furnace in a Murrieta attic, we already know where to look: the hardened door gasket, the filter rack gaps, the dried-out plenum tape. That’s the difference between a cleaning crew that clears visible dust and a specialist who finds why it keeps coming back.
We run Rotobrush and Nikro extraction systems, purpose-built negative-air and brush equipment designed for thorough debris removal from duct interiors. Our Abatement Technologies gear stays ready for elevated contamination jobs where simple vacuum extraction won’t cut it. We know Honeywell and Aprilaire filtration products because clean ducts are the foundation of clean indoor air; a premium filter is wasting its life on a dirty supply trunk. We’re familiar with how Trane equipment connects to and depends on clean duct paths, and we carry the OEM-compatible gaskets, filter frames, flex duct collars, and high-temperature mastic these systems need.
One thing we don’t do is pretend to be Trane. We’re state-licensed, insured and bonded, and we work on Trane equipment as an independent service provider. No manufacturer authorization, no warranty endorsement. What that buys you is honest diagnosis; we have no factory relationship to protect when we tell you a part is worn out or a coil needs replacement rather than another cleaning.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Trane Air Duct Cleaning Problems We Fix in Murrieta
- Hardened cabinet door gaskets on XR and XB furnaces. Trane’s upflow and downflow cabinet gaskets harden and shrink in Murrieta’s triple-digit attic summers. When that gasket dies, return air bypasses the filter entirely and coats the evaporator coil in a fine layer of dust. We replace the gasket with an OEM-equivalent part and clean the now-fouled coil before resealing the cabinet.
- Slide-in filter rack gaps on Trane air handlers. The factory filter racks on many Trane air handlers leave open gaps around the frame edges. That gap lets attic or garage air get pulled directly into the return path, loading the blower wheel with lint and fine debris. We seal the rack frame with mastic and re-seat the filter so the only air coming into the system has passed through media.
- Variable-speed air handler dust accumulation on XV20i and XL18i systems. Variable-speed Trane systems run at low airflow for long stretches. That’s great for comfort, but it lets ultra-fine dust settle and adhere to the evaporator fins and blower wheel unless the ductwork is sealed and balanced. We see this on XV20i systems throughout Murrieta’s larger two-story stucco homes, especially after long shoulder seasons.
- Dried-out taped seams and unsealed takeoffs on older Trane supply trunks. Homes built during Murrieta’s 1990s-2000s housing boom often have original hard-pipe supply trunks with taped seams and unsealed takeoffs at the plenum. In a Southwest Riverside County attic, that tape bakes and releases, dumping conditioned air into the insulation while pulling fiberglass particles into the airstream. We strip the old tape and reseal with mastic rated for high-temperature attic service.
- Sagging flex-duct runs in 15- to 25-year-old Murrieta homes. A big share of Murrieta’s housing stock was built between the late 1990s and early 2010s, which means flex duct that’s been sitting in 140-degree attics for two decades. Sagged runs create low points where dust, pet hair, and horse-stall debris collect, and disconnected joints pull attic air straight into the supply side. We inspect, re-support, and reseal every flex connection we touch.
If you can’t remember the last time your ducts were cleaned, that’s usually answer enough. For Trane in Wildomar and Murrieta, it’s not just dusty, it’s horse dust: wind-blown decomposed granite and dry arena fines from surrounding equestrian properties make every Trane system here work harder and clog faster.
Trane Parts & Our Repair-vs-Replace Approach
For Trane equipment, we use OEM or OEM-equivalent door gaskets, filter frames, flex duct collars, and mastic rated for high-temperature attic service. Generic hardware-store tape and thin flex fail too fast in Southwest Riverside County heat; we’ve pulled off miles of the stuff that crumbled to dust the moment we touched it. We keep common Murrieta-sized flex diameters, gaskets, and collars on the truck so we don’t leave a system half-reassembled while parts ship from a warehouse.
Our repair-vs-replace rule is simple and honest. If a Trane air handler or evaporator coil is badly contaminated, rusted, or has been flooded with bypass dust for years, cleaning it repeatedly is selling you a problem instead of fixing one. We’ll tell you plainly when replacement is the right call and quote it straight. Sometimes the most professional answer is “this coil is done.” Call (855) 341-7672 and we’ll walk you through what we find.
Our Trane Service Process – Step by Step
- 1
Diagnosis. We open the air handler and inspect the blower wheel, evaporator coil, return plenum, and cabinet gasket. On Trane systems we check the XR/XB door seals and slide-in filter rack gaps specifically, along with visible flex runs and plenum takeoffs.
- 2
Sealing and prep. Damaged gaskets come out, new OEM-equivalent parts go in. Open filter frame gaps get sealed with mastic. Sagging flex gets re-supported. Leaking plenum seams get stripped and resealed before we ever run the extraction equipment.
- 3
Cleaning. We run Rotobrush or Nikro negative-air extraction through every supply branch and return run, including the trunk lines. The evaporator coil and blower wheel get cleaned with proper fin combs and soft brushes, not a pressure washer that drives debris deeper.
- 4
Verification. We inspect each trunk and branch after cleaning, confirm the filter seats tightly, and run the system through a full cycle. You see before and after photos of your own ducts so you know the work actually happened.
- 5
Documentation. We note what we found, what we sealed, and what we’d watch going forward. No warranty confusing language; just a clear record of your system’s condition on the day we serviced it.
See the difference
Before
After
Before
After
Before
AfterTrane Products We Service & Install in Murrieta
Our Murrieta techs work on the Trane platforms most common in this area’s 1990s-2000s housing stock and newer builds. We service the XR80 and XR90 single-stage gas furnaces, the XB13 and XR13 air conditioners, the XV20i and XL18i variable-speed heat pump systems, and the S9V2 and S8X2 gas furnaces. Full system cleaning, duct sealing, and evaporator coil cleaning are all part of the work. We also stock and install the flex duct, collars, filters, and seals that keep these systems moving clean air through the whole house.
We Also Service These Brands
Our team works on Lennox and Carrier systems throughout Murrieta and the Temecula Valley, plus Trane repair in French Valley, as well. The equipment brand changes, but the physics don’t: sealed cabinets, clean coils, balanced airflow, and unfouled blower wheels. If you have a mixed-brand home or manage rental properties with multiple equipment lines, one call covers all of them.
FAQs – Trane Air Duct Cleaning Service in Murrieta
The door gasket on the XR80’s blower cabinet hardens and shrinks after years of sitting in a Murrieta attic, which opens a gap that lets unfiltered return air bypass the filter and pull attic dust directly into the system. We replace the gasket with an OEM-equivalent part and seal the cabinet before cleaning the dust that already got through. If your filter area always has a ring of fine powder around it, that’s the gasket talking. Call (855) 341-7672 and we’ll inspect it.
Yes. Variable-speed Trane systems like the XV20i and XL18i run at low airflow for long durations, which lets fine dust settle and stick to evaporator fins and blower wheel blades. A system that runs slow is a system that’s collecting debris more efficiently than a single-stage unit at full blast. Sealed and balanced ducts keep that settlement to a minimum, so we treat every XV20i cleaning as a sealing job too.
In most cases, yes. We access the coil through the air handler cabinet, remove the access panel, and clean the fins in place with proper coil combs and soft brushes. We’re not pulling the coil out unless it’s rusted, physically blocked, or the cabinet design makes access impossible. That keeps your system intact and your labor cost reasonable.
The ductwork itself isn’t Trane-branded; what matters is how it was installed and sealed when the Murrieta home was built. We see a lot of original 1990s-2000s hard-pipe supply trunks with taped seams that have failed in attic heat. The fix is the same regardless of equipment brand: strip the old tape, reseal with high-temperature mastic, and close the takeoff gaps. We do that work on Trane, Lennox, and Carrier systems alike.
No. Duct cleaning and sealing is performed on the air distribution system, not on the furnace, heat pump, or condenser components that Trane’s warranty covers. We don’t modify or replace factory parts unless they’re already failed, and we don’t touch sealed refrigerant lines. As an independent provider, we’re not claiming to act on Trane’s behalf, and nothing we do re-engineers the equipment itself.
Whole-system Trane air duct cleaning in Murrieta typically runs between $450 and $900 for a full supply-and-return cleaning with plenum sealing, depending on square footage and system access. Larger two-story 3,000+ square-foot homes with multiple trunks and long flex runs land at the higher end. We don’t quote per-vent pricing and we don’t bait with a $99 special that triples when the van arrives. One flat price per system, agreed before work starts, with before and after photos of your own ducts. Call (855) 341-7672 for an exact quote; estimates are free.
Book Your Trane Service in Murrieta, CA
We’re at work in attics across Murrieta every week, from the older ranch-style homes in the town core to the big two-story tract houses off Murrieta Hot Springs Road. If your Trane system is pushing dust, smelling like a barn when the AC kicks on, or running harder than it should, call (855) 341-7672 and we’ll get it diagnosed.
Written by Clay Gentry, Owner at Duct Cleaning Murrieta, serving Murrieta since the mid-90s.